ALUMINUM AIR PIPING INSTALLATION
Leak-free aluminum compressed air piping — designed, sized, and installed to replace rusty steel and stop wasted compressor capacity. Serving Burlington, Greensboro, High Point, Winston-Salem, Lexington, and surrounding central North Carolina.
LEAKY OLD PIPE IS A UTILITY BILL YOU PAY EVERY MONTH
Up to a third of your compressed air can be escaping through corroded joints. A tight aluminum system pays for itself.
COMPRESSED AIR PIPING DONE RIGHT — DESIGNED, NOT GUESSED
Most compressed air problems don't start at the compressor — they start in the pipe. Rusted black iron sheds scale into tools and filters. Threaded joints loosen and leak. Undersized headers starve the far end of the shop no matter how big the compressor is. We design aluminum piping systems from your actual CFM, run lengths, and layout, so every drop delivers full pressure and every joint stays tight.
JT Elite Air installs modern press-fit aluminum air piping for garages, body shops, manufacturers, and plants throughout central North Carolina — Burlington, Greensboro, High Point, Winston-Salem, Lexington, and the surrounding areas. New systems, steel pipe replacements, expansions, and compressor room tie-ins, staged so your production keeps running during the changeover.
Zero Rust
Corrosion-Free For Life
Fast Install
Minimal Downtime
Leak-Free
Press-Fit Connections
COMPRESSED AIR PIPING SERVICES
From a single new drop to a full plant re-pipe, this is the compressed air piping work we handle across central NC. Not sure what your system needs? Call and describe the shop — we'll point you the right way.
System Design & Layout
Loop and header design sized from your real CFM, run lengths, and future growth — so the far end of the shop gets full pressure, not an afterthought.
Complete Aluminum Installations
Full plant piping in modern press-fit aluminum — headers, drops, ball valves, and outlets — installed clean, labeled, and leak-free.
Steel & PVC Pipe Replacement
Rusted black iron, corroded galvanized, and dangerous PVC swapped out for aluminum. We stage the work to keep your air on during changeover.
Pressure Drop Correction
Tools starving at the end of the line? We find undersized headers, choked fittings, and bad routing, then re-pipe the sections that cost you pressure.
Leak Surveys & Repair
We locate the leaks bleeding your compressor dry, quantify the CFM loss, and fix them — or show you when replacement beats another round of patches.
Shop Expansions & New Drops
New bay, new machine, new production line? Aluminum extends in hours, not days — new drops and outlets exactly where the work happens.
Moisture Management & Drainage
Headers pitched correctly, drops that take air off the top of the pipe, and drain points that keep condensate out of your tools and finish work.
Compressor Room Piping
Clean connections between compressors, receivers, dryers, and filters — with isolation valves and bypasses so one machine down doesn't stop the plant.
Pipe Sizing & Flow Calculations
Header and drop sizing calculated from flow and distance — not guessed. Built with headroom for the next compressor, not just today's.
Energy Savings Analysis
We put numbers on what leaks and pressure drop cost you in kilowatt-hours, so the piping quote comes with the payback math attached.
Tie-Ins to Existing Systems
Transition fittings mate aluminum to threaded steel, copper, and stainless — so upgrades can phase in without ripping everything out at once.
WHY ALUMINUM BEATS STEEL PIPE
Black iron and galvanized pipe were the standard for decades — and decades later, they're the reason your filters clog, your tools spit rust, and your compressor runs longer than it should. Aluminum fixes the root cause, not the symptom.
- Never corrodes — clean air and a smooth full-bore interior for the system's life
- Press-fit joints stay tight — no threading, doping, or welding that leaks later
- Lightweight and modular — expands or reconfigures in hours when the shop changes
- Lower pressure drop — smaller energy bills for the same air at the tool
Quotes With the Payback Math Attached
Before you spend a dollar on pipe, we survey your system, estimate what leaks and pressure drop cost you in electricity, and quote the aluminum install next to those numbers. If the payback isn't there, we'll tell you that too.
Request a Piping Survey
AIR PIPING INSTALLATION ACROSS CENTRAL NC
Looking for a compressed air piping contractor near you? We design and install aluminum systems throughout the Piedmont Triad and surrounding central North Carolina — find your area's page:
- • Burlington
- • Greensboro
- • High Point
- • Winston-Salem
- • Lexington
- • Graham
- • Mebane
- • Thomasville
- • Kernersville
- • Piedmont Triad
One Contractor, Whole Air System
The crew that pipes your plant also services your compressors and dryers — so the header size, dryer capacity, and compressor controls all get designed as one system, not three separate quotes.
Call (336) 290-6372ALUMINUM AIR PIPING — FAQ
Why choose aluminum air piping over black iron or galvanized steel?+
Steel pipe rusts from the inside out. That rust flakes into your air stream, chokes filters and tools, and rough corroded walls create pressure drop that forces your compressor to work harder. Aluminum piping never corrodes, keeps a smooth full-bore interior for the life of the system, weighs a fraction of steel, and installs with press-fit connectors instead of threading and doping every joint — so the install is faster, cleaner, and leak-free from day one.
How much compressed air am I losing to leaks in old pipe?+
In an older threaded-steel system it's common to find 20–30% of compressor output escaping through corroded joints, cracked fittings, and abandoned drops. Every 1 CFM of leakage is horsepower you're paying for around the clock. We can survey your existing system, estimate the leak load, and show you what a tight aluminum system saves in real electrical dollars — the payback math usually speaks for itself.
Can you install aluminum piping without shutting down my production?+
In most plants, yes. Aluminum systems assemble quickly with calibrated push-to-connect and clamp fittings — no cutting oil, no threading machine, no welding permits. We typically build the new header alongside the old one, then make the changeover during a planned window, a weekend, or off-shift hours so your production keeps running on the existing system until the swap.
What size aluminum air pipe does my shop need?+
Pipe size depends on your compressor's CFM output, the length of the runs, and how much pressure drop you can tolerate at the far end. Undersized headers are one of the most common problems we find — the compressor makes plenty of air but the pipe starves the tools. We calculate the header and drop sizes from your actual flow and layout, and design in room for the next compressor, not just the current one.
Can aluminum piping tie into my existing compressors, dryer, and steel pipe?+
Yes. Aluminum systems have transition fittings for threaded steel, copper, and stainless connections, so we can tie into your existing compressor room, dryer, filters, and receivers cleanly. Many customers replace the distribution headers first and keep serviceable equipment connections, then phase out remaining steel sections as budget allows.
Is aluminum air piping worth it for a small shop?+
Often, yes. Small shops feel leaks the hardest because a single 5–10 HP compressor has no spare capacity to waste. A compact aluminum loop with properly placed drops costs less than most owners expect, goes in fast, and ends the cycle of chasing leaks in old steel or fixing sagging, popped PVC (which should never carry compressed air — it shatters). We quote small shops and full plants alike.
REQUEST A PIPING QUOTE
Tell us about the building — square footage, compressor size, how many drops you need, and what the current pipe looks like. We'll follow up fast with next steps or a scheduled site visit.
Back to main site